1 117 MB 117000 - - -

Complete cylinder base 4700 cc

-

1 107/2 47NB 67785 - - -

Cylinder base 4700 cc

-

2 115 MB 64189 - - -

External cylinder liner 4700 cc

-

2 115 MB 64188 - - -

Cylinder liner for internal cylinders 4700 cc

-

3 107 MB 55704 - - -

Front crankshaft support

-

4 103 1532 50488 - - -

Intermediate crankshaft support

-

5 103 1531 53488 - - -

Prisoner for crankshaft support

-

6 107 MB 55703 - - -

Rear crankshaft support

-

7 107 1536 54014 - - -

Head to crankcase fixing stud

-

8 107 0747 MB 72648 - - -

Engine oil sump

-

9 103 1820 51406 - - -

Oil sump bulkhead

-

10 103 1531 53660 - - -

Prisoner on front crankshaft support

-

11 107/2 MB 65620 - - -

Clutch side oil duct closing plug

-

12 GN 48052 - - -

Gasket Ø 24,5x32

-

13 117 MB 117579 - - -

Front crankcase cover complete with studs

-

13 117 MB 117580 - - -

Complete crankcase front cover with hub and chain tensioner

-

13 117 MB 117581 - - -

Complete crankcase front cover

-

14 107/2 MB 61424 - - -

Gasket for engine front cover

-

15 107/2 MB 61859 - - -

Gasket for front cover with oil calibration

-

16 115 MB 67878 - - -

Ignition advance reading index

-

17 VNT 33020 - - -

Screw Ø 5x0,8x12 for fixing ignition advance reading index

-

18 DNT 47046 - - -

Nut 5x0,8x5 for coil lug

-

19 PN 55923 - - - new

Crankshaft cap fastener Ø 8x1,25x73

$32.15

20 PN 41864 - - -

Captive Ø 8x1,25x102 fixing front crankshaft support

-

21 RAT 45680 - - -

Washer 8x15

-

22 DNT 47031 - - -

Hand brake lever fixing nut Ø 8 x 1,25 x 6,5

-

23 RAT 46736 - - -

Elastic washer ANT 51003 Ø 12x24x1,2 for motor shaft support stud bolt

-

24 RNT 47085 - - - new

HARDENED STEEL WASHER

$1.02

25 DN 47061 - - - new

Nut 12x1x10

$2.73

26 GRN 54501 - - -

Nut 8x24 centering cup to cylinder block

-

27 PN 49099 - - - new

Stud 7x1x30 fixing sump to crankcase

$6.42

28 RNT 47210 - - -

Flat washer

-

29 DNT 47080 - - -

Nut 7x1 butterfly control shaft

-

30 PN 51443 - - -

Captive Ø 7x1x114 for fixing the cup to the crankcase on the rear side

-

31 DST 67465 - - -

Nut Ø 7 x 1 x 13,4 CH 11

-

32 PN 32424 - - - new

THEADED STUD - DOUBLE END

$4.00

33 RSN 32635 - - -

Split washer for alternator mounting

-

34 PN 46582 - - -

Prisoner fixing timing gear shaft Ø 6x1x19

-

35 GRN 50669 - - -

Crankcase head centering screw

-

36 32662 - - - new

THREADED STUD

$2.44

37 TN 48178 - - - new

GALLEY PLUG 20mm x 1.5

$12.80

38 GN 51444 - - -

Gasket 20,5x26x1,5

-

39 GOM 50315 - - - new

78 x 1.2 CYLINDER LINER ORING

$3.54

40 BNT 47016 - - -

Bolt 6x1x12 fixing oil seal bulkhead in the sump

-

41 RDI 53899 - - -

Toothed washer 6x10

-

42 PN 48126 - - - new

Stud 11x1,5x48 connecting starter motor to crankcase

$7.51

43 RNT 32423 - - -

Washer Ø 11,2x22x2,5

-

44 RSN 33667 - - -

Split washer Ø 11,5x19x2,2

-

45 DN 48127 - - -

Nut 11x1,5

-

46 TN 50677 - - - new

Oil drain plug from sump Ø 30x1,5

$36.40

47 GN 33367 - - -

Gasket 10x40x1 for sump oil drain plug

$2.44

48 PN 33927 - - -

Locknut Ø 10x1,5x38 for right engine support fixing

-

49 RAT 45681 - - -

Elastic washer Ø 10,5×18×0,8

-

50 DNT 47024 - - -

Nut fixing starter motor Ø 10 x 1.5

-

51 PN 35771 - - -

Brake and clutch pedal holder cover fixing Ø 6x18x28

-

52 RNT 67011 - - -

Washer 6 (for USA)

-

53 RSN 32690 - - -

Split washer 6x11x1,5

-

54 DNT 47047 - - -

Nut 6x1x5

-

55 BN 54015 - - - new

Bolt Ø 12x1,5 x180 for fixing basement to the head

-

56 RN 60913 - - - new

Normal washer Ø 12x22x3

$5.23

57 DN 66854 - - -

Nut 8x1.25x6.5 for fixing carburetors

-

58 GRN 51124 - - -

Nut 12x8,5x22

$13.55

59 PN 53525 - - -

Stud Ø 10x1,5x80 for fixing oil pump body and cover

-

60 GRN 55499 - - -

Nut Ø 14x11,5x34 between body and cover

-

61 DST 48923 - - -

Nut 10x1,5 for fixing oil pump to the support

-

62 PN 33921 - - - new

8x1,25 captive bolt to oil pump cover support

$17.91

63 RNT 55379 - - -

Flat washer clutch assembly fixing Ø 8

-

64 DST 53397 - - -

Stop nut 8x1

-

65 ANT 67794 - - -

Sealing ring 100x120x12 for drive shaft on clutch side

-

66 GN 47208 - - -

Washer Ø 10,5x16x1

-

67 TN 65967 - - -

Cap Ø 10x1,5x15,5 for water drainage from crankcase

-

68 GOM 42229 - - - new

Grommet Ø 11 x 16x2,5 under crankcase front cover

$1.75

69 TN 44295 - - -

Ø 6x1 plug for oil holes in front crankcase cover

-

70 PN 53067 - - -

Stud 8x1,25x38 on the oil pump body on the grub screw side

-

71 PN 48761 - - -

Clutch bell Ø 8x1,25x63 fixing cap

-

72 TN 33915 - - -

Cap Ø 20x1,5 for closing the crankshaft hole in the crankcase

-

73 GN 33916 - - -

Gasket Ø 20x26x0,5 for the cap of the hole of the crankshaft

-

74 ANT 43421 - - -

Sealing ring Ø 50x68x10 in the front cover of the crankcase

-

75 ART 49584 - - -

Stop ring Ø 40 E. for bearing seal on front cover

-

76 107/1 MT 62822 - - - new

Gasket for right cylinder head

$113.87

77 107/1 MT 62823 - - - new

Gasket for left cylinder head

$113.87

78 107/2 MB 63811 - - -

Right engine support

-

79 107/2 MB 63812 - - - new

Left engine mount

$85.00

80 PN 33919 - - - new

Prisoner 10x15x40 fixing left engine mount

$17.30

81 PN 73146 - - -

Captive bolt for fixing sump to crankcase and gearbox control support Ø 7 x 1 x 34

-

82 RAT 45679 - - -

Washer Ø 6

-

83 BNT 51436 - - -

Bolt for fixing front cover to crankcase Ø 6x1x18

-

Consignment

Consignment

Maserati / Bora / T-02 - engine block