1 DST 48102 - - - new

Nut Stop 6x1x10 ch. 10 for cylinder head cover fixing stud

$1.19

2 135900064 - - - new

331/66/25 WASHER $0.75

3 PN 50196 - - -

Stud 6x1x56 for cylinder head cap union -

4 PN 33904 - - -

Prisoner 6x1x10 for cylinder head cover fixing nut -

6 3032 47506 - - - new

Right cylinder head cover $1,594.86

7 3033 47507 - - -

Cylinder head cover exhaust side $581.90

8 3096 46962 - - - new

Inner side exhaust cover gasket $36.12

9 3098 46963 - - - new

External side exhaust cover gasket $36.12

10 3034 42135 - - -

Cover on head -

12 3060 50235 - - -

Cap -

13 1008 47486 - - - new

Internal gasket for head $19.12

14 GN 32408 - - -

Gasket for cylinder head oil introduction cap -

15 1002/47503 - - -

Nail 3x10 for chain fixing cap -

16 CHN/50253 - - -

Spacer tube for cap and chain for head oil inlet cover -

17 3063/50252 - - -

Spacer tube -

18 3061/50250 - - -

Chain seal for oil inlet cap -

19 3065/50257 - - -

Chain plate for chain sealing of head oil cap -

20 6060/41541 - - -

Spring fixing plate -

21 3035/46798 - - -

Cover on the head for oil introduction -

22 GOM/43143 - - -

Change used arqua from the east -

23 1006/47366 - - -

Gasket for cylinder head and crankcase -

24 1626/42376 - - -

Centering pin between head and crankcase -

25 PN 48700 - - - new

330/30/59 SPACER $2.20

27 DNT/47047 - - -

Nut 6x1x5 сh. 10 for fixing the air conditioner control shaft to the support and fixing the support to the dashboard -

28 RN/47075 - - -

Washer 8x17x2 for hand brake lever pins . -

30 PN/45720 - - -

Stud Ø 8x1x37 -

31 1502/49915 - - -

Cylinder base -

32 DNT/47064 - - -

Stem fixing nut (GD) -

33 RAT 45679 - - -

Washer Ø 6 -

34 DN/43118 - - -

Nut Ø 8x1,25x8 ch. 11 for fixing manifold to head . -

36 PN/49752 - - -

Stud 8x1.25x2.4 for chain tensioner fixing to crankcase -

37 PN/35766 - - -

Stud 6x1x54 for fixing water pump to crankcase . -

38 RAT 45680 - - -

Ateco spring washer Ø 8,4x0,8 washer -

39 DNT/47082 - - -

Nut 8x1x8 ch. 14 washer -

40 PN/49987 - - -

8x1.25x80 captive bolt for fixing front motor shaft support -

41 1531/49978 - - -

Stud on front motor shaft support -

42 1630/42016 - - -

Centering pin for crankshaft support -

43 1802/49823 - - -

Motor cup -

44 1530/49547 - - -

Front support for crankshaft . -

46 RAT 46736 - - -

Elastic washer 13x24x1 -

47 DN 47061 - - - new

Nut 12x1x19 ch. 19 $2.73

48 1522/49315 - - -

External cylinder liner 1st and 6th cylinder -

49 1522/47517 - - -

Exhaust valve seat -

50 GOM/50315 - - -

Grommet 70x1,2 for barrel -

51 GRN/42477 - - -

Bolt 8x24 for centering cup to crankcase -

52 BNT/47016 - - -

Bolt 6x1x10 for fixing bulkhead in the sump -

53 RAT/45679 - - -

Washer Ø 6.4x11x0.5 fixing flange and pocket -

54 1532/48721 - - -

Intermediate support for crankshaft -

55 1534/48719 - - -

Rear support for crankshaft -

56 1820/46727 - - -

Bulkhead on crankcase -

57 PN/32415 - - -

Locknut Ø 5x0.8x23 for fixing flange connections to intake manifold -

58 ANT/46735 - - -

Seal ring in the rev counter cover -

59 RN/41768 - - -

Washer 5,4x13x2 for nut fixing tachometer cover on head -

60 DNT/47046 - - -

Nut Ø 5x0,8x4 ch. 8 for throttle levers and articulated fasteners . -

61 3064/48044 - - -

Central cap -

62 3074/48104 - - -

Cap for distribution shaft -

63 1062/42011 - - -

Centering screw for timing shaft cap -

64 DN/32634 - - -

Nut Ø 8x1,25 ch. 14 for fixing distributor to cover. -

65 RNT/47075 - - -

Washer 8x17x2 on pin for lever on brake and clutch pedal shaft -

66 PN/42020 - - -

8x1.256x1x70 captive nut for distribution shaft cap fastening . -

67 DN/39651 - - -

Blind nut with washer 14x1,5x22 ch. 19 union head to base -

68 DNT/47100 - - -

Blind nut 14x1,5x19 ch. 22 for cylinder head to crankcase connection. -

69 1020/46809 - - -

Intake valve seat -

70 1022/47536 - - -

Intermediate cylinder liner -

71 PN 32424 - - - new

Captive Ø 8x1,25x32 manifold header fixing $4.00

72 RSN/32635 - - -

Split washer 8.5x15.5x1.7 for nut -

73 DN 33691 - - -

Nut 8x1.25x8 ch. 12 -

74 PN/46469 - - -

Stud 8x1x1.25x46 for clutch support connection to crankcase -

75 PN/45725 - - -

Stud 8x1x37 for clutch holder connection to crankcase -

76 PN/36933 - - -

Prisoner 7x1x86 for joining the sump to the crankcase rear side -

77 1531/47060 - - -

Motor shaft support captive -

78 PN/47063 - - -

Prisoner 8x1x7 for fixing crankshaft supports -

79 TN 50677 - - - new

Plug 30x1,5x12 for oil drain from the sump $36.40

80 GN/33367 - - -

Gasket 30,5x40x1 cap .

$2.44

81 RNT/47101 - - -

Washer 14x26x3 for nut connecting head to crankcase -

82 1536/47578 - - -

Stud for fixing head to crankcase . -

83 PN 49099 - - - new

Washer 7x1x20 for fixing cup to crankcase $6.42

84 RNT/47210 - - -

Flat washer Ø 7x13x1,5 -

85 DNT/47080 - - -

Nut Ø 7x1x5 ch. 11 for butterfly shaft -

86 3046/46730 - - -

Cover for rev counter connection -

44197 GOM 43814 - - - new

Rubber grommet 41x47x3 for front and rear cylinder head cover. $1.72

Consignment

Consignment

Maserati / 3500 GT/GTI / T-01 - engine block